Most hunters obsess over broadheads and bow speed, then shoot a shaft that was never matched to their setup. Spine is the one variable that quietly decides whether your groups tighten or scatter at 50 metres — and it’s the one most people guess at. Get it right and everything downstream gets easier. Get it wrong and no amount of tuning will save the build.
250–400
Goshawk Spine Range
3
Numbers That Decide It
1″
≈ 5 lb Draw Weight
±.001″
Straightness Tolerance
1. What Spine Actually Measures
Spine is stiffness — nothing else. It is measured by laying a 28-inch shaft across two supports, hanging a 1.94 lb weight at the centre, and recording how far the shaft sags. That sag, in thousandths of an inch, is the spine number. A shaft that deflects four hundred thousandths of an inch is a 400 spine. One that deflects two hundred and fifty thousandths is a 250.
Which means the numbering runs backwards from what most people assume. A lower number is a stiffer shaft. A Goshawk 250 is the stiffest arrow in the line; a 400 is the most flexible. Hunters new to the system regularly order a 400 thinking they’re getting the heavy-duty option, when they’ve actually picked the lightest and most forgiving shaft we make.
Spine is also not arrow weight, and it’s not durability. A 400 is not weaker in the sense of breaking more easily — it flexes more under load. Weight is a separate specification measured in grains per inch, and the two move together only because stiffer shafts need more carbon. Across the Goshawk line that runs from 7.1 GPI on the 400 up to 9.5 GPI on the 250.
“Spine isn’t a preference. It’s an output. Your bow decides it, and your job is to read the answer correctly.”
African Reaper Arrows — Field Notes
2. The Three Numbers That Decide Your Spine
Three measurements do almost all the work. Everything else is a refinement.
Draw Weight
More force at the string means more force trying to bend the shaft at release. Heavier bows need stiffer shafts. This is the input everyone knows about, and it’s the one hunters tend to over-weight in their thinking — because on its own it tells you very little. A 70 lb bow can legitimately take anything from a 250 to a 350 depending on the other two numbers.
Arrow Length
This is the input most hunters underestimate. A longer shaft has more leverage against itself, so it behaves as though it were weaker even though the carbon hasn’t changed. Read across any row of the chart below and you’ll see the recommendation step stiffer as length grows.
The practical rule, taken straight off our own chart: one inch of arrow length moves your spine requirement about as much as 5 lb of draw weight. That’s why cutting a shaft down stiffens it, and why two hunters shooting identical 65 lb bows can need different spines if one draws 28 inches and the other draws 30. Measure your actual arrow length — nock throat to the end of the shaft, not including the point — rather than assuming it matches your draw length.
Point Weight
Mass at the front resists acceleration while the back of the shaft is being driven forward, which bends the arrow harder. Heavier points make a shaft act weaker, so they demand more stiffness to compensate. Stepping from a 100 grain field tip to a 125 grain broadhead is enough to move the recommendation a full spine step in parts of the range — which is exactly why our chart has a separate tab for each.
One more modifier worth naming: bow type. Traditional bows shoot off the shelf or close to it and are released with fingers, so the arrow has to flex further around the riser to get clear. A trad bow generally needs a weaker spine than a compound of the same poundage. The Spine Selector asks for bow type for precisely this reason.
3. Reading the Goshawk Spine Chart
Below is our 125 grain reference — the most common broadhead weight for South African plains game. Find your draw weight down the left, your arrow length across the top, and read the intersection.
| Draw Weight | 26″ | 27″ | 28″ | 29″ | 30″ | 31″ | 32″ |
|---|---|---|---|---|---|---|---|
| 40–45 lb | 500 | 500 | 400 | 400 | 400 | 350 | 350 |
| 45–50 lb | 500 | 400 | 400 | 400 | 350 | 350 | 300 |
| 50–55 lb | 400 | 400 | 400 | 350 | 350 | 300 | 300 |
| 55–60 lb | 400 | 400 | 350 | 350 | 300 | 300 | 300 |
| 60–65 lb | 400 | 350 | 350 | 300 | 300 | 300 | 250 |
| 65–70 lb | 350 | 350 | 300 | 300 | 300 | 250 | 250 |
| 70–75 lb | 350 | 300 | 300 | 300 | 250 | 250 | 200 |
| 75–80 lb | 300 | 300 | 300 | 250 | 250 | 200 | 200 |
| 80–85 lb | 300 | 300 | 250 | 250 | 200 | 200 | 200 |
Three things to notice. Values shown in solid black fall inside the Goshawk range and you can order them today. Greyed-out 500 cells sit above our range — very light, short setups that we don’t currently build for. Red 200 cells sit below it, at the extreme end of heavy draw weight and long arrows, where you’d be looking at a specialist shaft.
Notice also how wide the 300 and 350 bands are. Between them they cover most serious hunting setups in this country, which is why the Goshawk 350 is our most-ordered spine. It sits at the centre of the 55–70 lb, 28–29 inch window that describes the majority of South African compound hunters.
If you’re shooting 100 grain tips, the chart shifts a step softer in places — the Spine Selector holds both tables and will apply the right one once you enter your point weight, along with your bow type. It takes about twenty seconds and removes the chart-reading error entirely.
4. What Happens When You Get It Wrong
A mismatched shaft doesn’t fail loudly. It fails as inconsistency — the flier you can’t explain, the group that opens up past 40 metres, the broadhead that plans off target when the field tips were grouping fine. Hunters usually blame the rest, the release, or themselves long before they question the shaft.
Under-Spined (Too Weak)
Shaft flexes excessively at release · Arrow paradoxes outside the riser · Fishtails on launch · Loses energy fighting itself in flight · Groups open up at distance.
Over-Spined (Too Stiff)
Shaft refuses to flex around the riser · Porpoises vertically · Kicks off the rest · Bleeds energy on launch · Tunable only with band-aids.
A matched shaft does something specific and recognisable: it flexes just enough to clear the riser, then recovers cleanly and flies straight. The diagnostic is bare-shaft testing. Strip the fletching, shoot at 15 to 20 metres alongside a fletched arrow, and watch where the two impact. When bare-shaft and fletched impacts converge, your spine is right. When the bare shaft consistently lands left or right of the fletched group, it’s telling you the shaft is fighting the bow and your vanes have been masking it.
Signs Your Spine Is Off — Quick Reference
Broadheads don’t group with field tips — the classic symptom. A blade up front amplifies any steering error the shaft is already making.
Groups are fine at 20m, scattered at 50m — a shaft recovering badly looks acceptable up close and gets worse with every metre of flight.
You’ve chased rest and nock adjustments for weeks — if tuning keeps nearly working, the shaft is likely the fixed variable you haven’t changed.
Visible wobble leaving the bow — ask someone to film from behind at slow motion. Fishtailing means too weak; porpoising means too stiff.
5. Spine vs. FOC — Don’t Confuse Them
These two get tangled constantly, so it’s worth separating them cleanly. Spine is how stiff the shaft is. FOC is where the weight sits along it. One governs how the arrow behaves at release; the other governs how it behaves on impact. They are different properties and you need both right.
The trap is that one adjustment moves both. Add 50 grains to the front of your arrow and you have raised your FOC — good for penetration — but you have also made the shaft act weaker, which may have just pushed you out of spine. This is the single most common way a careful build goes wrong: a hunter chases high FOC for penetration, never revisits the spine, and ends up under-spined with excellent weight distribution and mediocre accuracy.
The order of operations matters. Decide your point weight first, because it’s driven by what you’re hunting. Then find the spine that matches your bow at that point weight. Then adjust inserts and shaft length to fine-tune FOC within the spine you’ve landed on. Work in that sequence and the two stop fighting each other.
For the penetration side of the equation — FOC targets, total weight, and how the two trade off at hunting distances — our piece on why hunters are switching to lighter arrows covers the ground in detail. And if you’re wondering why every Goshawk shaft is built on a 4.2mm inside diameter, that’s its own story.
The Bottom Line
Spine isn’t a matter of taste and it isn’t something you work out by feel. Your draw weight, your arrow length and your point weight produce an answer, and that answer is either right or it’s costing you accuracy you’ll never diagnose from the shooting line.
Measure your arrow length properly. Know your actual point weight, broadhead included. Then read the chart, or let the tool read it for you, and bare-shaft the result to confirm. Ten minutes of this is worth more than a season of tuning around a shaft that was never going to work.
Stop guessing your spine.
Enter your bow setup and get the exact Goshawk spine you should be shooting — point weight and bow type included.